Recoat Epoxy Garage Floor

FLOOR & PATIO - Benjamin Moore & Co.
A premium quality, quick-drying, epoxy-modified acrylic satin latex floor enamel. One coat covers most previously painted surfaces that are in fair to good condition. Recommended For . recoat and service times. Withstands light traffic after overnight ... Return Document

NSP SPECIALTY PRODUCTS NSP 122 Industrial Floor Coating
Self-leveling epoxy floor coating. This 100% solids formulation provides excellent protection for areas Uses: New construction or concrete restoration projects – Commercial Garage Service Manufacturing Areas and Aisles Minimum Recoat Time @ 77F/25C: 6 hours Maximum Recoat ... View Document

EPOXY/POLYASPARTIC FLOOR CHIP KIT
KIT can be used to beautify garage floors, basement floors, Recoat: Full Cure: 2 hours 2 - 4 hours 4 - 8 hours Mix Ratio: 1 part A: 1 part B by volume Pot Life: 20 - 30 minutes at EPOXY FLOOR CHIP KIT is not toxic. ... Content Retrieval

GP4844 GenerAl Polymers PAce-Cote Floors Polyaspartic
Or an optional topcoat for a variety of recommended floor systems. GP4844 pace-cote will adhere to a properly prepared concrete substrate. the recoat window is 2-6 hours. If beyond the 6 hours, over any smooth epoxy (primer or base coat) ... Doc Viewer

Aquapon® 35 Polyamide-Epoxy Gloss 95-1 Series
Aquapon® 35 Polyamide-Epoxy Gloss 95-1 Series Aquapon 35 is ideal for surfaces that require a chemical and abrasion To Recoat: 24 hours Volume Solids 53.6% +/- 2%* Weight Solids 69.1% +/- 2%* Mixed VOC 3.31 lbs./gal - 397 g/l* ... Read Here

TK-EPOXY FLOOR CHIP KIT - Welcome To TK Products
EPOXY FLOOR CHIP KIT can be used to beautify garage floors, basement floors, TK Products, division of the Sierra Recoat: Within 24 hours Full cure: 1-3 days POT LIFE @ 70° F: from manufacturing defects, and are fit -30 minutes ... Read Content

Shield-Crete™ Concrete Floor Epoxy
Concrete Floor Epoxy . RECOMMENDED USES • Garage Floors • Patios and Walkways • Pool Decks • Athletic Courts • Basement Floors PRODUCT AT-A-GLANCE CHARACTERISTICS . Recoat: Minimum 8 hours . Maximum 5 days . Light traffic: 8-12 hours . ... Read Content

About Experts Sitemap - Group 164 - Page 4 2012-07-20
You can produce a nice smooth dance floor with an epoxy coating over paint, garage: I would clean the floor, and fill the cracks with It can be applied over sealed grout. You would not apply it to raw grout. It is designed to recoat and blend in with itself so that there ... Read Article

Taubmans Aquafloor Water Based Epoxy
Taubmans Aquafloor Water Based Epoxy is an environmentally friendly two pack epoxy coating for garage, • Recoat Time 4 hours at 20°C and 65% RH (minimum) The floor may be professionally ground if acid etching is not possible. ...

Basecoat Application- Applying Your Basecoat & Color Chips

BASECOAT APPLICATION
Applying your Basecoat & Color Chips

What You Need:
•Basecoat (Parts A & B)
•3/8 Nap Roller
•Threaded Broom handle
•Paint Brush
•Painters Tape
•Spike Shoes
•Color Chips
•Latex Protective Gloves
•Paint Stick or Jiffy Mixer


Norklad WB is a two component water based epoxy coating. It is low odor, eco friendly, non flammable and has excellent adhesion with a long lasting finish. This high gloss epoxy color coat is formulated for excellent hide as well as abrasion resistance.

To begin, slowly add Basecoat Part B to Basecoat Part A. After the two parts are combined; mix well with slow speed mixing equipment such as a jiffy mixer or paint stick until the material is thoroughly mixed and streak free.

Be sure to also scrape the sides of the can to ensure thorough blending. Allow the mixed material to stand 30 minutes for induction time. Always re-stir before use. Mixed material is usable for four to six hours.

After the material is thoroughly mixed, use a brush or small roller to cut in along the walls, expansion joints and hard to reach areas.

Prior to painting, you also have the option to tape off sections along your baseboards so you wont get epoxy on unwanted areas.

After you are finished cutting in, apply the base coat from the container in thin ribbons onto the concrete in small sections at a time. Start painting in the corner furthest away from the exit of the room. Use a clean 3/8 short nap roller to roll the material out onto the floor surface. New rollers must be free of loose fibers and can be removed by holding a strip of duct tape and rolling the roller up and down until all loose fibers are removed.

After painting approximately 6 feet from the starting point you should begin to apply the color chips. If you purchased multiple colors of chips, they should be mixed together in a separate container prior to beginning the application.

The chips are applied by tossing them upward toward the ceiling; allowing them to float down into the wet basecoat. We recommend very small pinches of chips at a time in a feeding the chickens type broadcast to ensure excessive amounts arent placed on the wet epoxy at one time. This also allows the chips to float down, spread out and disperse in a uniform coverage. We also suggest using spike shoes during the color chip broadcasting. This allows you to walk over the wet epoxy without disturbing it. Spike shoes provide you with the ability to fill in any missed or bare areas so you have a uniform coverage.

Continue painting onto the adjacent sections and broadcasting chips until entire floor is complete. Be careful not to drop chips in handfuls directly down onto floor, once chips are placed they cannot be moved. They can be painted over, if you apply chips unevenly.

If you chose to topcoat this product, you must first be sure that all of the solvents and water have evaporated from the coating during the curing process. Usually you are able to recoat after 8 hours.

You can test this by pressing on the coating with your thumb to verify that no fingerprint impression is left. If no impression is created, then the recoat or topcoat can be started.

When the end of the pot life has been reached, you will find that the material becomes hard to apply and will actually tend to roll back up onto the roller. Do not try to continue application when the coating has reached this step. Applications made at different times with differing environmental conditions, may show slight variations in gloss.

Before recoating or topcoating, check the coating to insure no epoxy blushes were developed. You will notice a whitish, greasy film or deglossing on the coating. If a blush is present, it must be removed prior to topcoating or recoating. A standard type detergent cleaner can be used to remove any blush.

Get Document

CONCRETE & GARAGE FLOOR PAINT
CONCRETE & GARAGE FLOOR PAINT PRODUCT DATA SEAL-KRETE® Epoxy-Seal is a ready-to-use, acrylic-epoxy blend formulated to resist hot tyre marks/pickup, chemicals, oil, grease Recoat: 6 hrs 4 hrs 2 hrs Light foot traffic: 36 hrs 24 hrs 12 hrs ... Read Document

PRODUCT DATA Epoxyshield
Epoxyshield® is a user friendly and easy to apply water-based epoxy garage floor coating with an ultimate adhesion and durability. The product has an excellent wear, impact and To recoat: 48 hours (suitable for normal foot traffic and heavy items) Full hardness 7 days ... Fetch Document

EPOXY FLOOR COATINGS - ::: General Polymers :::
EPOXY FLOOR COATINGS Advantages • High solids • VOC compliant low odor during installation • Easy to maintain Wash prior to recoat. Seal Coat 3505 (Stipple) Mixing and Application 1. Premix 3505A (resin) using a low speed drill and Jiffy ... Retrieve Content

ES82 Barricade Sealer And Finish - YouTube
Low gloss. Excellent durability (semi-permanent), ideal for scrub and recoat. Recommended for spray buffing with floor 3:10 Watch Later Error Floor Finish 2:45 Watch Later Error How to Apply Epoxy Sealer to Your Garage Floor by DannyLipford 9,473 views; Loading more ... View Video

GarageGuard Water Based Epoxy EGG-xxx Series
Recoat: 16 Hrs. @55°F 8 Hrs. @77°F 6 Hrs. @100°F Max. Recoat : 72 Hrs. @55°F garage floors and other concrete surfaces. Scrub floor with a stiff brush and strong detergent solution to remove all dirt, ... Read Full Source

046 - Guard Heavy Duty Epoxy Floor Screed
*DRY TO RECOAT / OVERCOAT 8 – 12 hours FULLY CURED 7 days *With same generic type paint. ADVANTAGES NATIONAL GUARD HEAVY DUTY EPOXY FLOOR SCREED SYSTEM Microsoft Word - 046 - Guard Heavy Duty Epoxy Floor Screed.doc Author: sabrij ... Fetch Content

CONCRETE & GARAGE FLOOR PAINT 50 Grams/liter
EPOXY-SEAL Low VOC White Base 960001 1 gallon 0 15944 96001 3 9 00 15944 96001 6 14 x 14 x 8 .91 / 42 4 45 cases EPOXY CONCRETE & GARAGE FLOOR PAINT 50 grams/liter WARNING! IRRITANT! Recoat: 6 hrs 4 hrs 2 hrs Light foot traffic: 36 hrs 24 hrs 12 hrs ... View This Document

Epoxy 100 Data - Arizona Polymer Flooring | Concrete Floor ...
EPOXY 100 PRODUCT DESCRIPTION AND USE residential garage floors and for many other commercial and industrial maintenance applications. Recoat .. 12-18 hours Light Traffic ... Retrieve Content

Terratuff Epoxy Floor Coating - Nuplex Construction Products
Recoat Time: Minimum 16 hours at 20°C Maximum 48 hours at 20°C Full Cure: Effectively cured after 48 hrs. Full: 7 Terratuff Epoxy Floor Coating Subject: A two pack pigmented, epoxy resin based coating system. Terratuff gives a smooth glossy finish. ... Read More

About Experts Sitemap - Group 164 - Page 16 2012-07-20
Epoxy flooring, tile grout: Thank you for your question Karen, Both epoxy and polyurethane are You can use the material just like you would on a garage floor but they are just as prone to damage as anything you should be able to recoat these areas with our Mex Seal. To get the ... Read Article

Floor Sign Epoxy
Floor Sign Epoxy is a two-component, high performance, self-leveling epoxy floor coating. Commercial Garage Service Manufacturing Areas and Aisles Aircraft Hangers Floor Sign Epoxy Physical Data: Minimum Recoat Time @ 77F/25C: 6 hours Maximum Recoat Time @ 77F/25C: ... Document Viewer

Roof Paint| Paint Coatings Ph 09 570 1461 - YouTube
Very active in the maintenance field, and is called upon on a regular basis, for advice and methods on how to repair or recoat many sufaces 0:42 Paint Chip Epoxy Floor Coating in Queen Creek Arizona #1 Etching 2:37 Jay Leno Chooses UCoat It Garage Floor Coating by UCoatIt ... View Video

95-4700 AQUAPON 4700 Clear Self-Leveling Epoxy
To Recoat*: 24 hrs. 24 hrs. 16 hrs.

Restaurant Flooring Kitchen-General Polymers Fastop S Urethane System-start

http://www.highperfsystems.com
http://www.mdseamlessflooring.com
http://www.restaurantfloors.org
http://www.foodprocessingfloors.org

Tokyo Seafood Grill Windsor Mill, Maryland

Max. Recoat**: 5 days 3 days 2 days *Suitable for light foot traffic. AQUAPON® 4700 Clear Self-Leveling Epoxy Freight Classification: PAINT OR PAINT RELATED MATERIAL Packaging: 5 Gallon Kit 1 Gallon Kit ... Return Doc

Epoxy Mastic
Contact Diamond Vogel Technical Service for detailed information on floor coating and immersion applications. RECOAT /TOPCOAT Recoat Time* [At 70°F (21°C)] general maintenance will prolong the integrity of all epoxy mastic coatings. For more detailed ... Doc Viewer